- 4000lb Capacity Max, Gear
Unit 1 HP Marathon/Leeson, 110 Volt and In-line GFCI, Lock
on Switch, 14' Electrical Wire Motor to Switch(1)
- Dual Pipe Bearing w/grease
fitting (2)
- Pulley Hangers 3/8 in.
thick x 2 1/2 in. x 12 in. Galvanized (4)
- 4 in. Pulleys *Galvanized
Plates* 4 in. Aluminum Sheave w/Bronze 5/8 Bushing on 5/8
Shaft - LIFETIME WARRANTY (4)
- 90 ft. Total 1/4 in.
Galvanized Aircraft Cable
- 1/4 in. Galvanized Drop
Forged Cable Clamps (12)
- Shackles 1/2" (8)
- Pontoon Chock Brackets w/
Bolts/Nuts (4)
- Bearing Bracket (4)
- 1/4" Thimbles (not shown in
diagram) (4)
- Cradle Beams - 5" x 9 ft
Length (other sizes available below) (2)
BUY NOW |
- 5000lb Capacity Max, Gear
Unit 1 HP Marathon/Leeson, 110 Volt and In-line GFCI, Lock
on Switch, 14' Electrical Wire Motor to Switch(1)
- Dual Pipe Bearing w/grease
fitting (2)
- Pulley Hangers 3/8 in.
thick x 2 1/2 in. x 12 in. Galvanized (4)
- 4 in. Pulleys *Galvanized
Plates* 4 in. Aluminum Sheave w/Bronze 5/8 Bushing on 5/8
Shaft - LIFETIME WARRANTY (4)
- 90 ft. Total 5/16 in.
Galvanized Aircraft Cable
- 5/16 in. Galvanized Drop
Forged Cable Clamps (12)
- Shackles 1/2" (8)
- Chock Pontoon Brackets w/
Bolts/Nuts (4)
- Bearing Bracket (4)
- 1/4" Thimbles (not shown in
diagram) (4)
- Cradle Beams - Choose
Between 5" x 9 ft, 5" x 9 1/2 ft, or 5" x 10 ft (2)
BUY NOW |
- 3000lb (6000 lb.
compounded) Capacity Max, Gear Unit 3/4 HP Marathon/Leeson,
110 Volt and In-line GFCI, Lock on Switch, 14' Electrical
Wire Motor to Switch(1)
- Dual Pipe Bearing w/grease
fitting (2)
- Compound Pulley Block
Hangers (4)
- 4 in. Pulleys *Galvanized
Plates* 4 in. Aluminum Sheave w/Bronze 5/8 Bushing on 5/8
Shaft - LIFETIME WARRANTY (4)
- 150 ft. Total 1/4 in.
Galvanized Aircraft Cable
- 1/4 in. Galvanized Drop
Forged Cable Clamps (12)
- Shackles 1/2" (8)
- Pontoon Chock Brackets w/
Bolts/Nuts (4)
- Compound Tie Off Bracket
(4)
- 1/4" Thimbles (not shown in
diagram) (4)
- Cradle Beam- 5" x 9', 5" x
9' 6", or 5" x 10' Length, 4" Welded Pulley, 4" Aluminum
Sheave, 5/8" Bronze Bushing, 5/8" Stainless Steel Bolt/Nut
With Grease Fitting
BUY NOW
|
Boat
Lift Pontoon Chocks
Lifts From The Floor Of Your Boat, Keeping Stress
Off The Pontoons. For 4 or 5 inch High Standard I Beam and a
Maximum Flange Width of 4 inches between bolts. For higher beams
you will need to purchase longer bolts locally
Boat Lift Pontoon Chocks - V
Will fit I beam 5" no wider than 4" on the
flange.
Pontoon Boat Lift Remote Control Unit
Remote Control Unit With Keychain Pendant.
Pontoon Boat Lift Dual Pipe Support
2 Hangers With Grease Fittings, Galvanized, For
2" Drive Pipe. 17" Wrapping Area.
Boat Lift Gear Unit Cover
2 Piece Grey Covers Front & Back of Gear Unit.
VIEW ALL PARTS
|
